Product Specification
| Dimension (D*W*H) |
90*290*170mm |
| Weight |
2.55kg |
| Input voltage |
DC11.50V-DC15.0V |
| AC output voltage |
AC230V +/-10% |
| Frequency |
50HZ +/-1Hz |
| Waveform |
pure sine wave |
| Soft start |
yes |
| Harmonic distortion |
THD 3% |
| Work efficiency |
93% MAX |
| AC output power |
1200W +/-10% |
| USB output |
DC5V-3A MAX |
| TYPE-C output |
5V3A/9V2A/12V1.5A support PD3.0 protocol, support QC3.0 protocol |
Features
1)Input Reverse Connection Protection
2)Input Under-voltage Protection
3)Input Overvoltage Protection
4)Output Overload Protection
5)Output Short Circuit Protection
6)Over Temperature Protection
Detailed Photos
Company Profile
Sunstone Power Co. was established in 2003 in manufacturing, market, and brand-name-building lead-acid batteries/battery plates.
Our factories (both plates factory & assembling factory) locate in Kunming City, Yunnan P.R. China. Since Yunnan P.R. is one of the main lead supply
areas, we have good advantages in quality control, delivery control, and cost control. So far we are the only factory that gets pollution control
permission from the government in Yunnan P.R.
Besides this, we set up our German company in Frankfurt in 2017 and an Indonesian company in Jakarta at the end of 2018.
We have our warehouse in both of these two countries. It gives fast delivery and stock support to European and Southeast Asian markets.
Partners
Certifications
Sunstone Power has been ISO9001, ISO14001 approved and soon on,m any of our products obtained CE, IEC ,VDS,RISTI(BY PT. TELKOM INDONESIA) certificates.
FAQ
Warning
· Do not allow children to use.
· Do not get the device wet.
· Do not touch the power plug with wet hands.
· Do not connect the output in parallel with the mains.
· Do not disassemble or modify the product without authorization.
· Do not place sticks or other metal objects in the air vents or other openings.
· Keep it well-ventilated. Do not place it in a place where flammable gas will be generated.
· Do not allow volatile or combustible substances to enter the product.
· Do not damage the output socket or cord.
· Do not operate the product in a high temperature and high humidity environment.
· Do not use the product in a common ground power system.
· Do not use it in medical devices without testing.
Operation
· When connecting the inverter and battery, proper cables should be used, and the operation should be standardized.
· Switching on or off of the inverter continuously and frequently may cause damage.
· The inverter is easy to drive resistive loads and switching power loads, such as induction cookers, rice cookers, TVs, and other devices. Within the nominal current or power range of the inverter, the nominal current or power can operate at full load because of its linear loads. Non-linear loads, such as electric drills, compressors, water pumps, etc., require a greater level of power than resistive loads to function properly. They require an operating current of about 2 to 6 times to start. If the inverter works with a full load, overload protection will start and it cannot be used normally.
Therefore, please confirm what type of load the device is and how much starting current or power it needs before choosing an inverter for your electronic device.
Using Environment
Place the inverter on a flat surface where the power cord can be easily secured. The location of the inverter should meet the following standards:
· Keep the ambient temperature in the range of 0~50°C.
· Keep dry. Keep away from moisture or water.
· Keep ventilated. DO NOT place objects around or on the inverter.
· Keep shady. DO NOT expose it to direct sunlight and DO NOT place the inverter near any heat-generating equipment.
· Keep away from all flammable materials.
Using Steps
1. Use the red DC cable to connect the positive pole of the battery to the red terminal of the inverter.
2. Use the black DC cable to connect the negative pole of the battery to the black terminal of the inverter.
3. After connecting the power cord, the LCD will display for 1 second, then the screen will be turned off and enter Sleep mode.
4. Short press the button to turn on the inverter.
5. Press the button three times to enter the Undervoltage Protection point setting mode. *The Undervoltage point is the default value of 11.75V.
6. In the setting mode, short press the button, and the Undervoltage Protection point can be selected. The selectable value is 11.75V = LFP (LiFePO4 battery) or 11.0V = LAD (Lead acid battery). After selection, press the button for 1 second. After successful setting, the normal
content will be displayed. If the button is not pressed within 10 seconds, the setting mode is exited.
){kind=link}